|
8200
TILE ADHESIVE
Reliable quality - from Cemix.
Basic tile adhesive for simple indoor applications.
- For small porcelaine stoneware and medium size ceramic tiles.
- For medium loads e.g. footfall of people: For kitchens, living rooms or hallways.
- C1: Adhesive strengths > 0,5MPa. For a wide temperature range from cold to hot.
- T: Reduced slip: For tiling from top to floor. Makes position stable tiling on walls easy.
- Frost-resistant in dry indoor environments.
- For unheated spaces. Not for floor heating.
Area of application
- Indoor: floor + wall
Processing method
- For hand processing
- Basic tile adhesive for medium and high absorbent ceramic tiles, decorative brick facings.
- Suitable for dry indoor environments e.g. kitchens, living rooms.
- Frost-resistant, also suitable for dry non-heated areas e.g. garages.
- Suitable only for light loads e.g. footfall of people.
Processing details
Learn more about technical details for processing this product.
Substrate requirement
The substrate must comply with the applicable standards, must be solid, free of loose particles, free of dust, paint, residues of demoulding agents and efflorescence. It must be sufficiently rough, dry and evenly absorbent. The surface shall not be frozen or water-repellent. The substrate shall be stable in volume and have required flatness.
Substrate preparation
Depending on substrate water absorption and climatic conditions, the following is needed: Use Cemix 2614 primer on absorbent substrates. If necessary, for non-standard substrates, modify with a suitable method to achieve the desired properties. Smooth unevenness of the substrate with suitable Cemix materials and allow to dry and cure. The substrate shall comply with applicable regulations, standards, or material manufacturer's recommendations.
Preparation of the mixture
Prepare the material by pouring the dry mixture into the prescribed amount of water and mixing it. Use potable water or water complying with EN 1008 to mix the mixture. Mix using a slow-speed mixer. Mix to a homogeneous, lump-free mixture and leave to rest. Then mix again briefly.
Water demand
| Quantity | Liters (Min) | Liters (Max) |
|---|---|---|
| 25 kg | 6.5 L | 7.5 L |
| 1 kg | 0.26 L | 0.3 L |
Mixing
Mixing time
5 min
Mixing speed in Rpm
800x/min
Ripe time
3 min
Processing instructions
First, apply a thin layer of the adhesive to the substrate with the straight edge of the stainless steel trowel. Then, apply sufficient adhesive for the appropriate layer with the notched side of the trowel, if possible in one direction.
Lay the tiles and adjust them within the open time period.
In case the open time is exceeded, do not tile anymore. The applied adhesive must be removed in this case.
In case of uneven substrates use buttering floating process : Apply adhesive as described also on the reverse side of the tile.
Clean the tile from fresh adhesive with a sponge trowel and clean water.
Application thickness
| Minimum layer thickness | 3 mm |
|---|---|
| Recommended layer thickness | 5 mm |
| Maximum layer thickness | 8 mm |
Consumption
Material consumption min.
1.6
Material consumption max.
6.3
Material consumption in measuring unit
kg/m²
Open time according to EN12004
>20 min
Working time (potlife)
180 min
Walkability after
48 h
Treatment after application
Non-absorbent tiles prolong the curing period.
Avoid sun, heat, humidity and draughts. Protect from frost. Direct heating of the surface is not permitted.
Tool and cleaning instructions
After finishing work, wash the tools immediately with clean water. Remove dried residues mechanically.
Smaller deposits can be removed with acetic (diluted acetic acid) or a special cement paint cleaner.
Technical parameters
| Main binder | Grey cement |
| Flammability class | A1 |
| Max. grain size | 0,7mm |
| Full load after | 7 d |
| Adhesive tensile strength after water storage in >N/mm²(EN12004) | 0,5 |
| Adhesion tensile strength after freeze thaw storage in >N/mm² | 0,5 |
| Adhesive tensile strength after dry storage in >N/mm² (EN12004) | 0.5 |
| Setting time and tensile adhesion after 20 min | 0.5 |
| Vertical slip (EN12004) | 0.5 mm |
Files
|
|